Engine Control for Ducati superbikes

• ECU

• Short PC adaptor cable N-7002  

• PC serial lead N-7001  

• CD with all software and maps

• Kit Includes lever & 2 part wiring loom with high quality Deutsch Autosport connector

• 10Kg preset shift load

• Pre-wired to plug directly into your bike 

• Less than 1mm of lever flex on up-shifts for switch activation, zero lever flex on back shifts

• Aluminium plate

• 2 x M6 screws & washers

• 4 x M4 screws, washers & Nyloc nuts

• Requires the installation of the development loom – N-7003

• Kit includes – Control module & one sensor

• Requires additional patch cable – N-7006

• Based on NGK UEGO

N-5002 Replacement wide band sensor for N-5001 lambda kit

• For use with N-5001 on bike lambda system

N-7006 Patch cable for bike mounted lambda system N-5001

• Requires the installation of the development loom    N-7003

M-163 Single input wide band lambda system M163 with display for dyno use

• Requires the installation of the development loom N-7003

• Based on a reference calibrated version of Bosch LS4

N-5006 Replacement wide band sensor for M163 lambda kit

• For use only with M163 display type lambda system

N-7011 Adaptor loom to plug in the M163 directly to a 749 / 999 / 1098 to get a lambda display on a standard bike

• Uses the lap time connector to get bike power

N-6001 Falcon race dashboard kit including all wiring and sensors

• 749 / 999 race bikes only

• Mounting brackets are included in the kit

• Steering stop positions need to be reduced

• Not compatible with IAW 5.9, only Nemesis

• No logging capability other than lap time & max RPM

• Compatible with infra red lap timing system
• Product data sheet 
• Product manual

N-6003 8Mb race data logger including base wiring loom

• Requires the installation of the development loom – N-7003

• Detachable USB communication cable & Data View Easy software included

• Connects directly to the development loom to capture via CAN all NEMESIS generated channels as well as lambda if it is fitted.

• The logger loom has one auxiliary connector enabling the user to add the N-7008 sensor loom for connecting the front wheel speed and 4 additional 0-5v sensors such as fork / shock / brake pressure / spare.

N-7008 Sensor input loom for use with the N-6003 data logging systems, permits the connection of the following sensors:

• Fork travel potentiometer

• Shock travel potentiometer

• Front brake pressure sensor

• Auxiliary sensor input

• Front wheel speed sensor

N-8001 Fork travel potentiometer with high quality Deutsch Autosport connector

• 150mm stroke

N-8002 Shock travel potentiometer with high quality Deutsch Autosport connector

• 75mm stroke

CS-VB10 GPS module for direct 'plug n play' integration with the N-6003 logger system

• 10Hz update rate

• Enables circuit computation plus additional channels for braking / acceleration / lateral G forces, altitude and rate of climb, turn radius etc.
• Data sheet for the CS-VB10 for use with Nemesis

DK-LOCK Data View - Advanced analysis software for use with our data logger kits as used in all high end motorsport.

• This software is activated by plugging in a USB key to your PC

DK RX / TX Infra red lap timing transmitter and receiver kit for 749/999/1098/848

• If no development loom is fitted, this plugs directly into your bike

• If the development loom is fitted you will require the additional patch cable  N-7005

• Kit includes a coded transmitter & receiver.

DK-RX Lap time receiver supplied as an individual part

• Will be coded to suit an existing transmitter so that multiple bikes can be run using only 1 transmitter

Looms may be specified for 

• ECU + dashboard only
• ECU + Dash + ECU logging, 
• ECU + Dash + ECU logging + chassis logging

Note that we we do not build this style of loom for road use. This is a 'racing only' product and does not include items such as turn signals or lights. Please contact us for full details of this 'custom' build service.

N-7003 Development wiring loom with extra connections for

• Lambda input

• Data logger kit N-6003

• Tilt switch

• Power pick up

N-7012 Mating 8 way loom connector + contacts for use with the N-7003 development loom where the N-6003 logger is not being used and the customer wants to adapt their own logger system to the Nemesis

• Deutsch – DTM04 8P

• Enables expansion of the development loom

N-7001 Replacement RS232 programming cable for Nemesis

• Identical to the one supplied in the base nemesis kit

• USB adaptor with 200mm of cable for connection to the standard N-7001 cable

• CD with original manufacturer drivers.

• Updated drivers are available here and also on the Nemesis system CD v13 onwards

For retail or trade enquiries please contact nemesis@competitionsystems.co.uk or call +44 (0) 8707 444 666 / Fax +44 (0)8707 444888

Keep checking this page for information updates on this product.